|
AUTOTECNICA GM0517228
|
|
$45.99
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$45.99
Total
|
|
|
|
|
|
| AUTOTECNICA GM0517228 Specifications |
|---|
| Average Current Draw | 7 | | Average Flow Rating | 140 | | Connector Color | Black | | Connector Gender | Female | | Connector Shape | Pin | | Depth | 300 | | Fuel Sending Unit Included | Yes | | Fuel Tank Pressure Sensor Included | No | | Fuel Type | Gas | | Gasket or Seal Included | Yes | | Gasket Or Seal Material | NBR/FPM | | In Tank or External | In Tank | | Inlet Fitting Thread Size | M16x1.5 | | Inlet Outside Diameter | 10 mm | | Inlet Quantity | 2 | | Inlet Thread Diameter | 14 MM | | Inlet Type | Thread | | Internal Or External Strainer | External | | Intlet Fitting Thread Size | M14x1.5 | | Length | NA | | Lock Ring Included | Yes | | Maximum Flow Rating | NA | | Maximum Pressure | NA | | Minimum Flow Rating | NA | | Minimum Free Flow Rate | NA | | Minimum Pressure | NA | | Mounting Hardware Included | Yes | | Negative Ground | Yes | | Outlet Outside Diameter | 12 mm | | Outlet Quantity | 1 | | Outlet Thread Diameter | 16 mm | | Outlet Type | Thread | | Pump Design | NA | | Pump Type | Electric | | Resistance Ohms Empty | 1.8 | | Resistance Ohms Full | 75 | | Strainer Included | Yes | | Tank Seal Outside Diameter | 86.3 mm | | Tank Seal Rim Shape | Round | | Tank Seal Thickness | 5.95 mm | | Terminal Gender | Female | | Terminal Quantity | 3 | | Terminal Type | Pin | | Universal Or Specific Fit | Specific | | Voltage | 12 | | Wire Colors | Black, Purple, Grey | | Wire Harness Included | Yes | | Wire Quantity | 4 |
|
|
Features & Benefits:
- Replacement of cracked or failing OE fuel pump and sender assembly corrects troublesome fuel management issues
- Seal should be replaced whenever pump or sensor module is removed and reinstalled
 Benefits of Purchasing a Fuel Pump & Housing Assembly Purchasing just the fuel pump is less expensive up-front, but a complete Fuel Pump & Housing Assembly provides added benefits:
- Extend Service Life: New strainer(s), hoses, sensors and other components help resolve problems that could be caused by more than just the pump.
- Reduce Install Time: Since you don't have to disassemble the housing, which could lead to damage, replacement becomes a simple swap, dramatically reducing installation time.
- Save Money: The cost of the assembly is often cheaper than buying the components individually, and means you only have to do the job once.
 Prevent Premature Fuel Pump Failure Preventing premature fuel pump failure is far less expensive and time consuming than continuing to replace the pump. There are three common causes for premature fuel pump failure:
| ELECTRICAL ISSUES |
Poor electrical connections will mimic symptoms of a failed pump, sometimes resulting in unnecessary replacement. Before replacing the pump:
- Use a Fuel System Tester to test pump pressure is within expected range
- Use an Electrical Tester to test for bad wiring, burnt or corroded connectors
- Check / Replace faulty Fuse(s) and Relay
BEFORE REPLACEMENT |
| FUEL CONTAMINATION |
Dirt, rust or debris in the fuel can clog strainers and stick to internal pump components. When replacing the pump:
- Replace Fuel Filter or Fuel Strainer
- Empty and clean the tank with Fuel Tank Cleaner
- Fill tank with fresh, uncontaminated fuel of appropriate grade
DURING REPLACEMENT |
| PUMP DAMAGE / OVERHEATING |
Running low on gas causes your fuel to heat up quicker, and your pump to work harder. After replacing the pump:
- Maintain at least 1/4 tank of fuel and use a Fuel Additive / Conditioner to keep pump cool and lubricated
- If vehicle is stored without use, drain tank to prevent pump corrosion from fuel oxidation
AFTER REPLACEMENT |
Attention California Customers - WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
|
| OEM / Interchange Numbers: 19179429, 25027457, 25028380, 25178863 |
Warranty Information:24 Months |
|
