|
CARTER P74643S
|
|
$133.99
Price
|
$0.00
Core
|
+ Sold in packs of 1x1
Pack
|
$133.99
Total
|
|
|
|
|
|
| The float arm (where pictured) may ship detached to prevent damage in transit. To connect, simply snap the wire end into the sender hole. |
| CARTER P74643S Specifications |
|---|
| Connector Shape | Threaded | | Fuel Sending Unit Included | No | | Fuel Tank Pressure Sensor Included | No | | Gasket or Seal Included | Yes | | In Tank or External | In Tank | | Inlet Type | Strainer | | Internal Or External Strainer | External | | Lock Ring Included | No | | Minimum Flow Rating | 18.5 | | Minimum Pressure (PS) | 43.5 | | Mounting Hardware Included | No | | Negative Ground | Yes | | Outlet Quantity | 1 | | Outlet Type | Hose connection | | Pump Type | Electric | | Strainer Included | Yes | | Terminal Gender | Male | | Terminal Quantity | 2 | | Terminal Type | Pin | | Voltage | 12V | | Wire Harness Included | No |
|
|
Carter Fuel Pump & Housing Assemblies decrease cost and labor time by ensuring a seamless repair from start to finish! Every Carter assembly includes features that bring exclusive benefits to each application. These may include:
- OE Matched Electrical Connections - Make installation simple
- Metal Clamps - Prevent blowoffs on the fuel supply hose
- Silver Alloy Buttons - Increase the life of the sender assembly
- over-Molded Armature - Reduces fuel flow turbulence
- Carbon Commutator - Eliminates oxidation and high electrical erosion
- Rubber Feet - Reduce noise and vibration during operation
- Float Arm - Pre-mounted and calibrated to ensure proper fuel read
- CleanScreen™ Technology - Internal and external filtration provides 40% more dirt-holding capacity (graphic below)
 Benefits of Purchasing a Fuel Pump & Housing Assembly Purchasing just the fuel pump is less expensive up-front, but a complete Fuel Pump & Housing Assembly provides added benefits:
- Extend Service Life: New strainer(s), hoses, sensors and other components help resolve problems that could be caused by more than just the pump.
- Reduce Install Time: Since you don't have to disassemble the housing, which could lead to damage, replacement becomes a simple swap, dramatically reducing installation time.
- Save Money: The cost of the assembly is often cheaper than buying the components individually, and means you only have to do the job once.
 Prevent Premature Fuel Pump Failure Preventing premature fuel pump failure is far less expensive and time consuming than continuing to replace the pump. There are three common causes for premature fuel pump failure:
| ELECTRICAL ISSUES |
Poor electrical connections will mimic symptoms of a failed pump, sometimes resulting in unnecessary replacement. Before replacing the pump:
- Use a Fuel System Tester to test pump pressure is within expected range
- Use an Electrical Tester to test for bad wiring, burnt or corroded connectors
- Check / Replace faulty Fuse(s) and Relay
BEFORE REPLACEMENT |
| FUEL CONTAMINATION |
Dirt, rust or debris in the fuel can clog strainers and stick to internal pump components. When replacing the pump:
- Replace Fuel Filter or Fuel Strainer
- Empty and clean the tank with Fuel Tank Cleaner
- Fill tank with fresh, uncontaminated fuel of appropriate grade
DURING REPLACEMENT |
| PUMP DAMAGE / OVERHEATING |
Running low on gas causes your fuel to heat up quicker, and your pump to work harder. After replacing the pump:
- Maintain at least 1/4 tank of fuel and use a Fuel Additive / Conditioner to keep pump cool and lubricated
- If vehicle is stored without use, drain tank to prevent pump corrosion from fuel oxidation
AFTER REPLACEMENT |
 Additional Resources
Fuel System Diagnostic Check-List
Attention California Customers - No Proposition 65 warning is required with this product.
|
| OEM / Interchange Numbers: E3VZ9350A, E3VZ9350AA, E3VZ9A407AB, E6VZ9350A, SP2014H |
CARTER Warranty Information:12 months: Carter Mechanical Fuel Pumps, Carter Fuel System Accessories. Limited Lifetime: Carter Electric Fuel Pumps and Assemblies.Warranty Details |
|
